基于断口分析的钛合金轮内部缺陷损伤容限

为进行某轮损伤容限设计,开展了裂纹扩展断口分析和仿真分析研究。由断口分析可知:疲劳源为一处内部自然缺陷;依据疲劳辉纹确定了裂纹扩展速率;在裂纹长度为2 mm附近,裂纹扩展速率明显增大,为第一、第二加载阶段转换区域;裂纹稳定扩展区裂纹长度与裂纹扩展速率呈双对数线性关系;应用列表梯度法和Paris公式法反推了第二加载阶段的疲劳寿命,与该阶段实际循环次数的最大误差是163%。裂纹稳定扩展阶段裂纹扩展仿真值与断口反推值吻合;非稳定扩展阶段仿真值与断口反推值的最大误差为-215%;基于以上研究,合理确定了某离心轮内部裂纹表面扩展停机检测周期。该类轮非稳定、失稳扩展阶段寿命占内部裂纹表面扩展阶段寿命的比例达248%~357%,因此准确计算具有重要意义。     

激光冲击强化对钛合金高温微动疲劳寿命的影响

为了解高温工作环境下激光冲击强化工艺(LSP)对钛合金材料微动疲劳寿命的影响,开展了强化前后TC11钛合金在室温、300°C和500°C下的微动疲劳试验并测试了试验件表层的残余应力及硬度。结果表明:随着温度的升高,激光冲击强化对TC11钛合金微动疲劳寿命的提高倍数逐渐减小。在轴向载荷为400MPa,法向载荷为65.5MPa时,经激光冲击强化后TC11钛合金试验件在室温、300°C和500°C下的微动疲劳寿命分别为强化前的5.5倍、3.5倍和1.7倍;强化后试验件表层的残余应力会在高温下发生松弛,且松弛程度会随温度的升高而增大,这是激光冲击强化效果随温度升高而逐渐弱化的主要原因。     

复合材料胶补飞机损伤金属结构疲劳寿命分析

针对复合材料单面胶接修理飞机损伤金属结构疲劳寿命分析时,多种失效模式耦合作用、残余热应力和附加弯曲力矩以及裂纹非均匀扩展的影响,提出了一种能够综合考虑上述影响因素的复合材料修理损伤金属结构疲劳寿命评估方法。算例分析结果与试验结果吻合,表明本文方法可为复合材料单面胶接修理损伤金属结构疲劳寿命估算提供参考。     

Investigation of dynamics of discrete framed structures by a numerical wave-based method and an analytical homogenization approach

In this article, the analytical homogenization method of periodic discrete media (HPDM) and the numerical condensed wave finite element method (CWFEM) are employed to study the lon-gitudinal and transverse vibrations of framed structures. The valid frequency range of the HPDM is re-evaluated using the wave propagation feature identified by the CWFEM. The relative error of the wavenumber by the HPDM compared to that by the CWFEM is illustrated in functions of fre-quency and scale ratio. A parametric study on the thickness of the structure is carried out where the dispersion relation and the relative error are given for three different thicknesses. The dynamics of a finite structure such as natural frequency and forced response are also investigated using the HPDM and the CWFEM.     

直升机主起落架疲劳试验技术研究

以直升机主起落架疲劳试验为对象，对试验内容、试验方法、试验实施及试验结果进行分析。通过试验验证确定了起落架的疲劳危险区域，并为优化零件结构提供了依据。     

基于对数正态分布的多部位疲劳结构的疲劳寿命预测方法

以实现多部位疲劳结构的寿命预测为目的,基于概率累积损伤法则,推导了基于寿命服从对数正态分布的概率疲劳寿命预测方法。根据损伤临界值与应力水平无关这一前提条件,将损伤临界值由传统确定性的值1转换为随机变量,累积损伤由确定性的中值损伤计算,建立了"中值累积损伤-概率损伤临界值"干涉模型。当对数寿命标准差恒定时,对比了所提出模型和基于Monte Carlo仿真的Miner累积损伤方法的寿命预测结果,验证了模型的准确性以及其方便快捷的优点;当对数寿命标准差变化时,损伤临界值由满足损伤等效的应力基准决定,此时亦可得到高精度的偏于安全的寿命预测结果。     

钉头型式对复合材料层合板机械连接强度的影响

通过3种不同铺层比例的复合材料层合板机械连接接头的挤压强度测试，研究了钉头型式对复合材料层合板机械连接挤压力学性能的影响，获得了沉头螺栓挤压强度修正系数。试验数据表明：采用沉头螺栓的复合材料机械接头 的挤压强度，可达到采用凸头螺栓的复合材料机械连接挤压强度的90%左右，但接头刚度仅为采用凸头螺栓的复合材料接头刚度的40%~50%。研究采用Hashin失效准则和Tan-Camanho损伤扩展方法，对两种钉头型式的复合材料层合板机械连接接头的挤压失效过程进行了有限元分 析，预测了复合材料层合板机械连接接头的偏移挤压强度和极限挤压强度，模型预测值与试验值的误差不超过15%。     

Fatigue crack propagation of new aluminum lithium alloy bonded with titanium alloy strap

A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction.     

Multiple-site investigation of the properties of an HF radio channel and the ionosphere using Digital Radio Mondiale broadcasting

The Digital Radio Mondiale (DRM), one of the new digital radio broadcasting standards, has been designed to overcome typical short wave radio channel difficulties, such as the multipath propagation and fast temporal changes of the received signal level, both related to the properties of the ionosphere along the path of propagation. In particular, some of the RF carriers used in the applied COFDM transmission technique serve to estimate the current state of the radio channel to enable the proper demodulation of the received signal.We have been detecting such RF carriers on select frequency channels (standard DRM broadcast) using a network of recording stations located in different parts of Poland in order to collect data on the HF radio channel. We have been also evaluating the usefulness of this procedure in providing information on the current state of the ionosphere in the refraction region between the transmitter and receivers. When the DRM system becomes more widespread, this method can supplement data that comes from the ionosondes, since it does not require much financial resources and the receivers can be easily scattered over a large area. This paper presents a set of experimental data and its analysis.     

改进的耐久性分析裂纹萌生方法研究

针对耐久性分析裂纹萌生方法所存在的影响其工程应用效果的 3个重要问题 ,加以研究和改进 .在结构使用载荷谱下进行一组模拟试件的耐久性试验 ;依据裂纹萌生寿命试验数据 ,用计算反推法确定结构细节裂纹萌生p s N曲线三参数式的参数cp;分析了对数裂纹萌生寿命标准差对经济寿命的重要影响 ,取该标准差值为飞机结构对数疲劳寿命的常用标准差值 0 .1 76～ 0 .2 ,从而建立了能够准确预测结构经济寿命的改进的耐久性裂纹萌生方法 .这种方法已在我国多种飞机结构的耐久性评定中得到成功的应用